Hangzhou Zhengdian Technology Co., Ltd.  

Product Name: Side Motor Remote Controller Magic Functions for Garage Door&#160; Model NO.: ZD-M01 Battery Type: AA Battery Material: Rubber Voltage: 12V Transmission Distance: 50-100m Universal: Universal Certification: RoHS, FCC, CE Type: Button Signal Transmission: RF Remote Control Application: Household Appliances Product Name: Uninersal Remote Coontroller Frequency: 315/433MHz Optional Usage: Garage Door,Roller Shutter, Door Opener etc. Trademark: ZD Transport Package: 1PCS/Small White Box, 500 or 600PCS/Carton Origin: China HS Code: 854370999 Product Description Side Motor remote controller Magic functions for garage doorProduct Description:Sidemotorcontrolkit3channelsButtonA:up, ButtonB:stopButtonC:downButtonD:lock Safeguard procedure:During the process of up or down, if switch failure or borken down, that motor can not stop itself, in this case, the motor will stop aumomatically after 3minutes working to protect motor and doors!Except the remote to controls, also available for manuel, with two buttons available on the receiver case, no need open the case, one button is learning button for add new remote, one button to control the motor up / down / stopController:1.Frequency:433MHz2.Motor Voltage:220VAC/50hz,Power<500W3.Remote spection:SA ABCD/12V27A,be learned about 50pcs control4.Motor:Side motor5.Safeguard procedure:during the process of up or down,switch failure that motor can not stop itself,after 3minutes will stop aumomatically to protect motor!6.Material:PVC7. Connection:2*4 wiring mouth 55698.Modulation system: amplitude ASK/OOK9.Receive Sensitivity(dBm):-95DB10.Working Tempeture: -10ºC~+70ºC11.PCB size/Weight:95*75*30mm/132g12.Outside case size/weight:125*85*38mm/68g13.One kit:one controller + two pcs transmitters14.Communication range:normally 50-100meters,test it base on actually circumstanceinstall instruction:1.Power off;2.First check the motor function,up /down/stop,all are right!3.Then check the wire to connection the right functionThere will be 6 pcs of different colors wireBlack Black:AC 220V votalogueRed:stopWhite/yellow: up/down(reverse)Green:CommonCheck the function with motor,if the same,connect directIf not pls adjust the wire till the same function4.Make sure the wire connection is right then test up function,if it is Down,pls reset the direction button in the side of controller.5.Pls use the antenna in the best place.6.Pls install the controller near the door to reach the best communication range7.Pls do not install in the rainyor sunshine place8.It should be at least 30 cm between the room ceiling and controller,at least 120cm between floor and controllerRemote set instruction: The receiver can work with one channel and three channel.You can judge it by the LED flash, the LED flash once and off,it is one channel, the LED flash three times and offonce, that means it is three channel.During learning process,LED flash lower and even1.how to learn the transmitterWe have matched transmitter and controller before ship,if you want to add additional transmitter,pls check below steps:2.learning status(make sure the same frequency and the same chip code):Press the learning button about 3s,led flash lower and even mean it is the learning statusPress any button in the remote for 2S,led off once,mean learn successfullyRelease the button,if led still flash lower and even,mean in the learning status,pls go on learning accrording above manual.During the process of learning,if there is not the remotes to be learned,about 3 seconds will stop the learning process,and LED flash same with working.3.Clear code:Press the learning button,LED flash lower and even,after 10s,LED flash quickly mean clear code is successfully(all remotes clear code,It can be learned about 50pcs of remotes)Controller instruction:The receiver can work with one channel and three channel.You can judge it by the LED flash, the LED flash once and off,it is one channel, the LED flash three times and off, that means it is three channel.For example:One channel:When button A learned in the controller,press button A once it open, press button A again it stop, press button A the third time it close.So same with button B/C/D,that mean one remote can control four gates.Three channel.How to change it to three channel?Press button D once, then press A and B at the same time, then press the button C. Whenthe LED flash three times and off, that means it is three channel.Function:Press button A it open, press button C it stop, press button B it close. Packaging & Shipping:Shipment:DHL,UPS,TNT,FedexandEMSorbysea/airoptionalPackage:Paperbox,polybag,blisterorasperyourrequest